Discharge diameter is 10-in, suction diameter is 12-in and sphere passage is 5-in. Impeller and volute cast from high chrome Gasite iron. The booster has only been used on one project. The Weedmaster attachment (8-feet) chops the weeds into small pieces - 3-5 inch (76-127mm) - to allow pumping into geotextile bags for decomposing or pumps them to the shore, up to 1km away, using the vegetation dredge pump. IMS Razor Tooth Weedmaster Cutterhead bolts directly to the IMS Model 5012 LP Versi-Dredge in place of the standard cutterhead. Location: State of Nebraska, USAĪquatic Weed Destroyer Cutterhead attachment for IMS 5012 Dredge Has been inspected and is in very good condition. Twin Disc MG 518-1 2.47 to 1 reduction sn 3 x 3918 rated 750 hp. Twin Disk MG 518 Marine Gear 2.47/1 reduction
Location: State of Nebraska, USAġ4-inch Cutterhead Module with Cutterhead and 65 hp driveĭredge works 65 HP cutter drive with pump and end ladder. Metso 8圆 slurry pump with drive and 50 hp motor. Metso 8" x 6" Slurry Pump w/ 50 hp electric drive GIW 12" x 10" Underwater Pump Location: State of Nebraska, USA Location: State of Oregon, USAġ2-inch Submersible Pump with Agitators Dragflow HY 300BĬomes outfitted with a hydraulically driven mechanical agitators, 250 ft of 10 inch fixed HDPE pipe, includes hydraulic power unit and associated controls. Pump comes outfitted with a jet ring, water supply pump, 2 saddles and a control box, 50 ft of electrical cord and 250 ft of 10 inch fixed HDPE pipe. Location: State of California, USAġ0-inch Submersible Pump with Agitators Toyo DP-150B Very low hours and in excellent condition. Min flow of 1200 gal/min and a max flow of 5000 gal/min. Non-clog design for high solids industrial pumping applications. Location: State of California, USAĮxcavator Pump Attachment 10-inch Eddy Pumps Min flow of 450 gal/min and a max flow of 2000 gal/min. Location: State of California, USAĮxcavator Pump Attachment 6-inch Eddy Pumps It was purchased for a specific job, it was never used again. Booster is reported to be in very good condition. It is powered by a John Deere 6090 diesel engine rated at 325bhp The dredge pump is a GIW model LCC-M250-660. The 10-inch pump is mounted on a steel base. The 10-inch booster pump is designed with centrifugal singles suction volute having a 12 inch diameter suction and is arranged for 10-inch inside diameter suction pipe. Fully boxed frame tubing for added protection Location: State of South Carolina, USAġ0-inch Booster Pump with Automation Package 4" x 10" box tube skid rails & 10" forklift boots. Hydraulic tank and diesel tank are both 120 gallons. Operating pressure 1200-3300 PSI with a hydraulic flow of 0-52 GPM. This HPU is driven by a Tier 4 Certified JCB Engine.
Location: State of South Carolina, USAģ300 PSI 25 GPM Hydraulic Power Unit (HPU) Discharge size is 4-in and suction size is 6-in. The Pump has a min flow of 250 GPM and max flow of 1200 GPM. The engine has liquid cooled, 12 Volt Power-in-Line 4 cycle Turbo Charge. The 4-inch Diesel Booster Pump has a 118-hp John Deere Engine.
Location: State of Louisianaġ6” Maddox booster pump powered by Detroit diesel 12v92T with a twin disc PTO driving a Falk gear box. Pump performance is 4,000 gpm (252 liter/sec) (51.8 m) TDH (water) 884 rpm.
Dredge pump is a GIW Cast Iron with discharge diameter of 10-in and suction diameter of 12-in. Powered by a John Deere 6090 engine with 325 bhp. Location: State of Florida, USAī1012-7X-03 built in 2008. 500 hp Dredge Cutterhead Module For 22-inch DredgeĤ8-inch Cutter Basket with 500hp hydraulic gearbox.
0 kommentar(er)
